请教ROLAND BOSS RC3如何升级

paulyang

请教ROLAND BOSS RC3如何升级

我的版本是1.20的，现在的是1.40的，改进了一些bug，我按照它官方网站的方法，没有能升级成功，如今还是1.20，希望有识之士能教教我。

谢谢~~~~~~~~~~！
以下是英文版本的。

Procedure for the update

NOTE
* You must not do the following operations on restoring. Doing so might make your computer freeze, or might result in the loss of all of the RC-3's data.

• Turn off the RC-3's power.
• Disconnect the USB cable.
• Allow your computer to enter suspend (standby) or hibernate mode, restart it, or shut it down.

• Connect an AC adaotor to your RC-3.
  * The RC-3 will not operate on USB bus power.
• Set the [
  OUTPUT LOOP
  ] knob and the [
  OUTPUT RHYTHM
  ] knob to the " MIN " position.
• Hold down the [
  TAP TEMPO
  ] button and the [
  WRITE
  ] button, and connect a plug to the OUTPUT A(MONO) jack. Then it will turn on and the display will indicate the "UP".
• Use a commercially available USB cable to connect the RC-3's USB connector to your computer's USB connector.
  When the RC-3 is recognized from your computer correctly, the display of the RC-3 will indicate "UP.".
  
• Open the "BOSS_RC-3" drive.
  [ Windows users ]
  Within My Computer (or Computer), open " BOSS_RC-3 " (or Removable Disk).
  [ Mac OS users ]
  On the desktop, open the " BOSS_RC-3 " icon.
• Copy (drag and drop) the "
  RC-3ROM.BIN
  " and the "
  ROMINFO.TXT" in the " rc3_sys_v140 " folder into the root directory (the same hierarchy as the " ROLAND " folder) of the " BOSS_RC-3 " drive.
• After the copy has been completed, unmount or remove the drive on your computer.
  * Refer to the step four of the " Connecting to Your Computer via USB " section in the owner's manual.
• Disconnect the USB cable from your computer.
  The RC-3's display will indicate the "
  U.P
  " after the connection is disabled correctly.
• Confirm the "
  U.P
  " message on the display and then push the [WRITE
  ] button.
  The display will indicate the "__".
• Push the [
  WRITE
  ] button again to start the update process.
  When it has completed, the display will indicate the "OK".
• After you confirm the update completion with the "OK" indication, remove the plug from the OUTPUT A(MONO) jack. Then it will power off.
  * The update program copied into the RC-3 will be removed automatically when the update has completed.
• Please verify the version number "1.30" with the procedure described in "How to tell the version" part of this document.

paulyang

paulyang

难道就没有人知道，没有人升级么？

942089662

buf 用修改吗。我啥都感觉不出来

paulyang

切换的时候有延迟~~~！所以roland做了升级。

你丫别跑

可以联系下罗兰中国

paulyang

感谢，感谢楼上的哥们~~！

942089662

小天使loop 做到了这点

rockyang874

升级完事儿了就不延迟了！？！？我擦，那就牛逼了。

rockyang874

哇哈哈，跟楼主一样是1.20。感谢楼主的帖子，才知道有升级这个事儿。升级成功了，果然不延迟了。
ps：罗兰中国压根没有更新程序，鄙视一下。跑到日本网站才下载到的。

syfWINDIR

同樣rc user路過，連usb線都沒有的說。。。

xuyi2007high

你们说  泥轰会不会用固件从USB口发起攻击？

英国豌豆

我也升级成功了 要感谢BOSS RC LOOP 中国交流群里的一位 大神帮助我省的级   还打算要卖掉rc3  现在看来 还得玩一阵子

[ 本帖最后由 英国豌豆 于 2014-1-20 22:15 编辑 ]

暴力婴儿XXX

哥们 群号是多少啊？？？麻烦告诉下！！谢谢