求助：想换个212的箱子，头子后面3个孔没看太懂

frququ · 发表于 2013-5-16 11:15:02

这两天想换个212的箱子但是头子后面的仨插口没看明白，看大概意思是用8欧的喇叭就用接口19 16欧的用接口20  接口21说明没理解，是不是两个8欧喇叭并联的话就用接口20和21各通一个？求解

19. Poweramp Output 8 Ohms: 8 ohms speaker output jack. Connect an 8-ohm cabinet or,       in the case of the Combo E310, its internal speaker here.       The Power Soak circuit sits between this speaker output and the power amp. You'll find some       important info on this circuit in section 22, please read carefully before operating the Power Soak!    CAUTION: The built-in Power Soak (22) may only be used in combination with an 8-ohm speaker       (or the E310 Combo's built-in loudspeaker) connected to jack 19!

20 Poweramp Output A -16 Ohms serial: 16-ohm speaker out, connected internally in series with       Output B (jack 21). Connect a 16-ohm cabinet here (Output A). Two 8-ohm speakers are connected       to Output A (jack 20) and Output B (jack 21), for example a combination of the internal 8-ohm       speaker of the Combo E310 and an external 8-ohm cabinet, e.g. the ENGL models E112 or E412.    CAUTION: If you intend to use a 16-ohm cabinet only, make absolutely certain you connect it to       Output A (jack 20).       Output B (jack 21) is only enabled when a speaker is connected to Output A (jack 20).    The built-in Power Soak (22) does not work with the two 16-ohm speaker outs!    Never activate the Power Soak when a speaker is connected to output A (20) or speakers       are connected to the outputs A and B (jacks 20 and 21)!    Power Soak deactivated (switched off): see chapter 22 for more information.

21 Poweramp Output B - 16 Ohms serial: This is an auxiliary output connected in series with Output A    (jack 20). This output is designed for one application for only—when you are driving a combination       of two 8-ohm cabinets\/speakers. This output may only be used when an 8-ohm speaker is       connected to Output A (jack 20). (See the example in chapter 20)    NOTE: Never operate the amplifier without a sufficient load, otherwise you may damage or       destroy the power amp!    When set to "Speaker Off," the Power Soak provides an adequate load for the power amp.    Speaker\/ cabinet options:       You can connect one 8-ohm cabinet to the 8-Ohm Output (19) in combination with the Power       Soak circuit and select any setting, or connect one 16-ohm cab to Output A (20) or two 8-ohm cabs       to Output A and B (20 and 21) without the internal Power Soak. Selecting the "Full Power" setting       deactivates the Power Soak!

frququ · 发表于 2013-5-16 11:16:31

厄。。挡住了。。15 16 17 后面4个依次顺延

frququ · 发表于 2013-5-17 21:05:04

各位大神给看看吧，过两天箱子该到家了，拜谢

麻脸小西 · 发表于 2013-5-17 21:25:47

提示: 作者被禁止或删除内容自动屏蔽

frququ · 发表于 2013-5-23 17:32:42

可能描述不太明白再上两张图就是是不是用A B出两条线通箱体上面那俩洞

烂设备（3号） · 发表于 2013-5-23 18:52:37

一条线，A接right IN

frququ · 发表于 2013-5-23 19:08:02

现在正在用的就是您所说的方法，好像是俩喇叭串联16欧，想研究下接两条线的套路，不知道是互不干扰成了8欧还是并联成了4欧

烂设备（3号） · 发表于 2013-5-23 19:26:16

原帖由 frququ 于 2013-5-23 19:08 发表
现在正在用的就是您所说的方法，好像是俩喇叭串联16欧，想研究下接两条线的套路，不知道是互不干扰成了8欧还是并联成了4欧

每个厂家的设计方式不一样箱体上2个接口是为了接2个不同箱头用的。而不是一个箱体与一个箱头的情况下还去接2个线

frququ · 发表于 2013-5-23 20:15:02

多谢多谢，受教了

zhangjialiang · 发表于 2013-5-23 22:08:38

lz 签名图片好牛逼啊[em28]

		自动登录	找回密码
密码			注册

求助：想换个212的箱子，头子后面3个孔没看太懂

回复 6楼烂设备（3号）的帖子

回复 8楼烂设备（3号）的帖子

求助：想换个212的箱子，头子后面3个孔没看太懂

回复 6楼 烂设备（3号） 的帖子

回复 8楼 烂设备（3号） 的帖子

回复 6楼烂设备（3号）的帖子

回复 8楼烂设备（3号）的帖子